View and Download Linksys PSUS4 user manual online. PrintServer for USB with 4-Port Switch. PSUS4 Print Server pdf manual download. View and Download Linksys PSUS4 quick installation manual online. PrintServer for USB with 4-Port Switch. PSUS4 Print Server pdf manual download. Also for. Printserver for usb, User guide, With 4-port switch • Read online or download PDF • Linksys PSUS4 User Manual.
|Published (Last):||14 November 2012|
|PDF File Size:||10.10 Mb|
|ePub File Size:||12.59 Mb|
|Price:||Free* [*Free Regsitration Required]|
Linksys is a registered trademark or trademark of Cisco Systems, Inc. Upgrading Firmware Appendix D: Windows Help Appendix E: Warranty Information Appendix H: Regulatory Information Appendix I: Connecting to the LAN Port Choose Destination Location Figure Select Program Folder Figure Copy Folder Figure Setup Complete Figure IP Address Llinksys Added Successfully Figure Connected Protocol Figure Searching for Device Figure libksys Bi-Admin Management Utility Figure Device Information Figure Verify Password Figure Printer Status Figure First, it lets you connect a USB printer directly to your network, eliminating the need to dedicate a PC to print serving chores.
Using a PrintServer frees up your “print share PC” Regulatory Information This appendix supplies the regulatory information regarding the PrintServer. Contact Information This appendix provides contact information for a variety of Linksys resources, including Technical Support.
Connect the other end of the cable into your networked linkksys, switch, or router. The distance between the PrintServer and the other device should not exceed feet meters.
Linksys PSUS4 User Manual | 2 pages
If it does not, click the Psuw4 button and choose Run. The Password screen, Figurewill appear next. Enter the default password admin in the field. The Basic Settings screen, shown in Figurewill appear. The IP Settings screen, Figureappears next. The Confirmation screen appears next. Your old and new settings will be displayed. If you want to make a change, click No and you will exit the Setup Wizard; You will have linmsys start the Setup Wizard again.
Linksys PSUS4 User Manual
When you see Figureclick User Install to continue. Click Exit to end amnual installation. The Welcome screen of the driver installation program, Figurewill appear first. You will need to close any other programs you have open before you continue. Click Cancel to quit the setup linkssy, then close the open programs. The next screen to appear is Select Program Folder, shown in Figure An icon will be added to the program folder listed.
You may change the name for the program folder, if you wish.
The Information screen appears next. Read the information, then click OK. The Printer Port Setup screen will appear, as shown in Figureand list the PrintServer and the connected printers. The Configure Printer Port screen will appear, as shown in Figure Your installed printer will appear in the field. Click the Connect button to connect the printer for configuration. To add another printer, click the Add New Printer button. PrintServer ‘s general settings.
Change these settings as described here and click the Save button to apply your changes or click Cancel to cancel your changes. The name can be located on a sticker that is on the bottom of the PrintServer.
Enter the name of the domain that you want the PrintServer associated with in the Domain Name field. This is especially useful for printing information when you are not connected to the network.
You can print from anywhere that you can access e-mail. Select from the following fields for each Logical Printer. Select the number from the drop-down menu of Logical Printer Port No: No values can be changed on this screen.
This screen is for information only. Clicking the Refresh button causes the PrintServer to retrieve this information again. Select the Exit tab and the screen in Figure will appear. Click the Yes button if you want to exit the Utility. Normally, the printer will be attached to a computer or other device that functions as an IPP Server.
This will be the same as your Browser configuration. Increase this number if you have a poor connection, or the remote server is very busy. The next screen to appear is Choose Destination Location, as shown in Figure You will be requested to choose the location of where the Bi-Admin folder will be installed.
If you want the folder to be installed in a different location, click the Browse button and select the location. If the Bi-Admin Management Utility icon has been created, you can just double-click on it instead. Any hardware found on the network will appear on the left-hand side of the screen, as shown in Figure manhal The Manul can be managed from this screen.
This option allows you to view the printer status, and set port and printer parameters. If you click this option, a Verify Password screen will appear, as linksus in Figure Make sure that you enter the password in the field before you click OK or an Incorrect Password message will appear. You may configure the PrintServer with this option. Typically only Macintoshes use AppleTalk, although other platforms can be made to use it with extra software. This value must be a fixed IP address.
Enter the Mail Account name and Password next. Enter the password again in the Confirm Password field. To add a cross segment print server, enter the IP address in the fields, and click the Set button. Click Cancel to undo any changes. For more information, click the Help button. Provided are possible solutions to problems that may occur during the installation and operation of the PrintServer. Read the descriptions linkss to help you solve your problems.
Common Problems and Solutions If the PrintServer is not working correctly, follow the advice in this chapter. manuaal
LINKSYS PSUS4 USER MANUAL Pdf Download.
In other words, the PrintServer will revert to its original factory configuration. I need to upgrade the firmware. In order to upgrade the linksya with the latest features, you need to go to the Linksys website and download the latest firmware at www. Linksys designed the PrintServers to function with both regular as well as bi-directional printers. Standard print servers cannot work with bi-directional printers, but the PrintServer features a custom design to support both parallel as well as bi-directional parallel interfaces.
Download the firmware from Linksys’s website at www. Open the Bi-Admin Management utility. Windows Help All wireless products require Microsoft Windows.
Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix.
PrintServer for USB with 4-Port Switch Buffer – A block of memory that temporarily holds data to be worked on later when a device is currently too busy to accept the data. Cable Modem – A device that connects a computer to the cable television network, which in turn connects to the Internet. Encryption – Encoding data to prevent it from being read by unauthorized people.
Ethernet – An IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium. Passphrase – Used much like a password, a passphrase simplifies the WEP encryption process by automatically generating the WEP encryption keys for Linksys products. Subnet Mask – An address code that determines the size of the network.