LGB 55025 PDF

For programming, you have to connect the to your DCC Command Station (see adjacent schematic). With the Chief from Digitrax the. With the LGB Multi-Train System, you can use the track to carry power and commands for your LGB switches, signals and accessories. You don’t need long, . Buy the LGB MTS Switch Decoder from Reynauld’s Euro Imports. Call us at

Author: Moogunris Goltizshura
Country: Panama
Language: English (Spanish)
Genre: Video
Published (Last): 10 December 2016
Pages: 275
PDF File Size: 10.54 Mb
ePub File Size: 18.25 Mb
ISBN: 285-5-64224-600-7
Downloads: 59931
Price: Free* [*Free Regsitration Required]
Uploader: Doubar

Forums New posts Trending Search forums. Calendar Monthly Weekly Agenda Archive. Media New media New comments Search 5025. Resources Latest reviews Search resources. Search Everywhere Threads This forum This thread.

MTS Turnout Decoder | Märklin

Everywhere Threads This forum This thread. Thread starter Darren Lalonde Start date 12 Dec For a better experience, ogb enable JavaScript in your browser before proceeding. Darren Lalonde Registered 12 Dec I am trying to program my switch decoder with the lgb software and interface.

The software recognises the device, but will not program it.

LGB 55025 Switch Decoder

I keep getting “Maximum Input Current Exceeded” and will not read eprom values. Any one got any ideas what i am doing wrong? From memory I think you need to attach at least one point motor to give it some “load”. Gizzy Railways, Aviation, Caravanning Darren Lalonde Registered 13 Dec Many thanks for all your replies. I have tried every wiring combination possible now. With and without motors, train on a track, etc, but still same message.


LGB 55025 MTS Switch Decoder – G Scale

The pc thinks it is doing something and spins round the 4 addresses, but doesnt actually write anything. I presume i should be able to read? If then try again it cant contact the I must have managed this somehow in the summer as i have two boxes, both on different address ranges. I just wanted to turn one lbg an on off rather than a point motor.


Hook the two together without going anywhere near a computer. Towards the rear of the 5502 you should find CVs for the various flashing and steady light modes. As the Meercat says “Simples”. Darren Lalonde Registered 17 Dec Hi Darren, what command station do you have?

Darren Lalonde Registered 18 55205 I have LGB Central station with the basic controller. What software are you using? Are you sure that the computer is talking to the ? Can you read the CV’s from a loco using the ? Lets start from the beginning. Have you read the instruction file loaded to your PC when you installed the software. Are you connecting the directly to thecomputer and points module with no lyb bits, track, locos, splitter units etc.

Is a switch motor connected to terminals A Do you need to unlock the switch decoder by changing a CV value – check your instructions.

Is your compatible with your version of windows – check the instructions. What COM port are you using.

I played around with my switch decoder with a universal remote controller using the supplied insert module for programming cvs into whatever and by changing the CVs in the to the assigned channel, or whatever. I don’t use a computer and had no problem producing steady current for lighting or flashing lights.


Connect up the as shown below: I’ve just tried reading the valued from a loco and the pc isn’t seeing reading these either.

I thought it was me doing something stupid. I’ve had my LGB stuff a long time but with kids and everything have only started to permanently install it in the garden and managed to program the decoders in the summer with the same laptop windowsstandard com port no usb and the standard lgb software.

I do this so infrequently i thought it was me. The only conclusion i can come to now is that my doesnt work any more. The same pc and software drive the fine and works the points, etc.

I just dont seem to be able to program any more. Well, if its all working as far as running trains is concerned, I suggest you find a local DCC’er to just set the address for you. You must log in or register to reply here. Facebook Pinterest Email Link. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.

By continuing to use this site, you are consenting to our use of cookies.