The AXB-REL8 controls closure-activated devices, acting as an eight-channel relay control port on the AxLink bus. Find great deals for AMX Axb-rel8 Access Relay Controller. Shop with confidence on eBay!. AMX AXB-REL8 Relay Controller | Consumer Electronics, Surveillance & Smart Home Electronics, Other Smart Home Electronics | eBay!.
|Published (Last):||3 October 2009|
|PDF File Size:||20.35 Mb|
|ePub File Size:||1.78 Mb|
|Price:||Free* [*Free Regsitration Required]|
Home Brands Categories Search.
If you are looking for the instruction manual: On this page you can download it for free. For details about manual, see the info below. The file is available in a few seconds as the connection speed of your internet. We believe that our webpage help you and we will be glad if you visit us in the future. PDF Click to preview. Is this manual helpful?
AMX AXB-REL8 download user guide for free – 5F |
Please click us here: Unless otherwise specified, OEM and custom products are warranted for a period of one 1 year. Software is warranted rell8 a period of ninety 90 days. Batteries and incandescent lamps are not covered under the warranty. AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform.
AMX AXB-REL8 Relay Controllers, Qty 2
This includes any lost profits, lost savings, incidental damages, or consequential damages. This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort claim including negligence and strict product liabilitya contract claim, or any other claim. This limitation of liability cannot be waived or amended by any person. This limitation of liability will be rle8 even if AMX Corporation or an authorized representative of AMX Corporation has been advised of the possibility of any such damages.
This limitation of liability, however, will not apply to claims for personal injury. Some states do not allow a limitation of how long an implied warranty last.
Some states do not allow the limitation or exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of the Limited Warranty may not apply. This Limited Warranty gives the owner specific legal rights. The owner may also have other rights that vary from state to state. The owner is advised to consult applicable state laws for full determination of rights.
Illuminate when associated relay is closed. Relay LED’s should amd panel control function.
Each device in the AXlink bus amd have a unique AXlink device number. If you later change the device number, remove and reconnect the AXlink connector. This enters the new device number into memory. The device number takes effect only on power-up. The device number must match the device assignment in the Axcess program. AMX assigns device numbers into the following three segments: The device number is the total of all of the switches in the ON down position.
The following table shows the switch numbers and their corresponding values.
Do not install relay wiring at this time. Refer to the following section for more information. Preparing captive wires To connect the wiring into a captive-wire connector: Insert each wire into the appropriate captive-wire connector up to the insulation. Tighten the captive screws to secure the fit in the connector. Rep8 Central Controller supplies power via the AXlink cable.
The maximum wiring lengths re,8 using AXlink power are based on a minimum of Connecting qxb Wiring The following paragraphs describe wiring connections for using the AXlink and relay connectors.
Checking the installation After set-up is complete: Check continuity of relay wiring. Check cable numbers and wiring, interfaces and sources against rrl8 documentation. Install tab strips to jumper between shared commons and clip off excess tabs. The dotted lines are used to indicate commons. Install supplied rel88 strips to jumper between shared commons. Clip off excess tabs and bend strip up, away from other wiring. Relay LED lights, but source does not activate: Check jumpers used for shared commons.
Check cable and source against supplied documentation. Check operational status of interface or source. Remove any connected relay and AXlink connectors from the rear panel. Remove the front panel and the space bracket behind the panel. Place the unit in the appropriate opening in the AC-RK.
Fasten the front panel to the rack and to the unit with the two screws you removed. AMX reserves the right to alter specifications without notice at any time.